Enamel KHS-510

Chemical composition

Enamel KHS-510 is a one-pack material based on vinyl chloride-vinyl acetate copolymer.

Recommended use

Enamel KHS-510 is designed for painting superstructures and freeboard vessels of unlimited navigation area.

Description

The service life of the coating is at least 2 years.

Coating from enamel of black color has a coefficient of brightness — no more than 1,5.

KHS-510 is applied on primed anticorrosive primers with steel, aluminum and clean wooden surfaces.

Certification

Hygienic conclusion of CGSEN acting throughout the territory of Russia. Certificate of conformity in the GOST R system.

Enamel is approved for use in shipbuilding and ship repair.

Specifications

by weight -28-36%, mass (depending from the color)

— by volume-13-17%, vol.

Thinners

Solvent P-4, butyl acetate or acetone in an amount not exceeding 20% ​​of the enamel mass.

Cleaning tools

Solvent P-4, butyl acetate, acetone.

Application

Surface preparation:

Pre-priming of the metal surface with primers such as VL, XC, EP.

It is allowed to apply old, hard-wearing anticorrosion coatings of the type ХВ, ХС, cleaned from contamination.

On the wooden surface, the enamel is applied directly to 2-3 layers.

Methods of application:

Pneumatic, airless spray, brush.

Application conditions:

Before use, make sure that the enamel is well mixed and uniform throughout the volume of the container.

If necessary, the enamel can be diluted to an operating viscosity of P-4, butyl acetate or acetone in an amount of no more than 20% by weight of the enamel before use.

The prepared enamel is applied to the surface of the protected material with a brush, roller, pneumatic or airless spray at an ambient temperature of minus 10 ° C to plus 35 ° C and a relative air humidity of not more than 80%.

To prevent condensation of moisture, the surface temperature should be above the dew point by at least 3 ° C.

After the enamel layer has dried (2 hours at 20 ° C), subsequent layers are applied.

For cleaning the tool, the solvents listed above can be used.

Precautionary measures

Material is flammable! Do not work near open sources of fire.

Work should be carried out with good ventilation, rubber gloves, using personal protective equipment.

Do not allow to enter the respiratory and digestive organs. If the material gets into the skin, wash it with warm water and soap.

Store enamel indoors in tightly closed containers, excluding direct sunlight and moisture at the ambient air temperature from minus 40 ° C to 40 ° C.

Storage

Guaranteed shelf life is 12 months from the date of manufacture.

Standard

TU 2313-020-27524984-2001

Product Features

By type of material

Enamel

By type of surface to be protected

Aluminum, Wood, Stainless steel, Ferrous metals, Primed metal

By field of application

Hydraulic and capacitive structures, Bridge structures, Shipbuilding and ship repair, Steel structures / Steel structures

By special properties

Anticorrosion protection of metal, Antiseptic for wood, Wear resistant coating, Outdoor, Mat / Frosted, Frost-resistant materials, Quick-drying coating

For resistance to impact

Moisture resistance, Wear resistance, Mold and fungus protection, Corrosion protection, Resistance to seawater, Weather resistance, Salt resistance, Oil resistance

By type of binder

KHS (copolymer-vinyl chloride)

 OOO KONDOR COMPANY

ATT.: SUPPLY DEPARTMENT !!!! R&LD !!

Moscow

8 (495) 790-14-52
8 (915) 218-57-47
Fax: 8 (495) 223-92-57
dann-25@bk.ru

Saint Petersburg

8 (812) 318-12-75
8 (812) 318-12-74